[Metalab] Blinkenrocket Bauanleitung

[overflo]

Ich hab fuer die BLINKENROCKET eine Bauanleitung gemacht.

https://www.youtube.com/watch?v=08FpkzmsDLY


Anbei ist das captions file.
Kannst du <Englisch> nach <Irgendwas anderes> uebersetzen?
Super DANKE!


Am 34C3 wird es 500 Bausaetze geben.
Einen grossen Teil davon gratis.. ;)



:*
-flo

-------------- next part --------------
1
00:00:04,680 --> 00:00:11,540
Put a little solder on the top right pad

2
00:00:12,420 --> 00:00:18,760
The MCU has a round mark, make sure it is at the  bottom left corner

3
00:00:20,620 --> 00:00:27,300
Carefully align the pins of the MCU 
with the pads on the PCB

4
00:00:28,220 --> 00:00:32,640
Melt the solder and fix the MCU in place

5
00:00:34,240 --> 00:00:39,120
It should now look like this.
Make sure the MCU has the correct alignment

6
00:00:39,540 --> 00:00:43,840
Now put the solder on the bottom row of the MCU

7
00:00:44,340 --> 00:00:49,460
Add solder on all four sides of the MCU.
It's OK if the pins are connected

8
00:00:50,240 --> 00:00:55,300
..now the top row

9
00:00:56,760 --> 00:00:59,060
..the left row

10
00:00:59,500 --> 00:01:04,060
and finally the right row

11
00:01:04,580 --> 00:01:07,920
Look at that mess you just made! :)

12
00:01:11,020 --> 00:01:13,660
Don't worry! 
Grab your desolder braid

13
00:01:14,000 --> 00:01:18,840
Put the desolder braid flat on the bottom row

14
00:01:19,420 --> 00:01:23,580
Apply some heat with your soldering iron and let the desolder braid soak in the solder

15
00:01:23,740 --> 00:01:28,880
Remove the desolder braid while it is still hot!
Do NOT try to pull it off with force!!
Just apply more heat if needed

16
00:01:29,320 --> 00:01:33,400
Cut off the used desolder braid

17
00:01:33,400 --> 00:01:39,820
Repeat what you just did on the next row

18
00:01:43,440 --> 00:01:48,000
Cut away.. Repeat the whole procedure on all four sides

19
00:02:05,480 --> 00:02:11,780
Clean the pins from solder leftovers by moving the soldering iron as shown

20
00:02:11,780 --> 00:02:15,020
You might want to clean the contacts now (optional)

21
00:02:15,020 --> 00:02:17,760
An old toothbrush and some contact cleaning solution will do

22
00:02:18,020 --> 00:02:22,080
Look at that!
Super nice!

23
00:02:22,600 --> 00:02:25,660
Add some solder to the top right pad for the EEPROM

24
00:02:26,040 --> 00:02:32,620
Beware: the EEPROM also has a small mark. 
Align it correctly

25
00:02:34,980 --> 00:02:41,780
Melt the solder
Place the EEPROM

26
00:02:41,780 --> 00:02:44,300
Solder the pins on the left side now

27
00:02:45,120 --> 00:02:47,840
One at a time should work for this part

28
00:02:48,280 --> 00:02:52,920
If you make a mess, just use the desolder braid like you did with the MCU

29
00:03:09,520 --> 00:03:13,580
Looks good?

30
00:03:15,180 --> 00:03:20,900
For the resistors always add solder to the first pad, place the part and solder the second pad

31
00:03:23,740 --> 00:03:27,820
Make sure to place the resistors on the right positions on the PCB

32
00:03:29,860 --> 00:03:33,800
Resistors have no polarity so orientation does not matter

33
00:03:35,680 --> 00:03:57,360
Just add one after the other and solder both contacts

34
00:04:03,320 --> 00:04:10,040
The capacitors we use in this design have no polarity. Just make sure to put them in the right place

35
00:04:11,380 --> 00:04:18,580
Attach them like the resistors.. First one pad, than the other. You'll know the drill by now.

36
00:04:45,160 --> 00:04:49,620
DIODES!
CAREFUL: Those have a polarity.

37
00:04:50,100 --> 00:04:52,340
Add solder to the right pads first

38
00:04:52,860 --> 00:05:06,260
The Diodes have a white mark it has to point to the RIGHT

39
00:05:15,440 --> 00:05:18,480
It should look like this.
Double check it now.

40
00:05:23,680 --> 00:05:28,480
Add some solder to the batteryholders pad.
Not too much, not too little.

41
00:05:31,040 --> 00:05:34,920
The batteryholder should be placed with it's opening towards the top of the rocket as shown

42
00:05:35,360 --> 00:05:38,300
Turn over the PCB and solder the four contacts of the batteryholder

43
00:05:40,440 --> 00:05:47,980
Make sure the batteryholder is placed flat on the PCB

44
00:05:51,320 --> 00:05:54,360
Looks like this? 
Good Job!

45
00:05:55,320 --> 00:06:02,960
Now insert the two buttons
They should snap right in

46
00:06:05,240 --> 00:06:12,080
Solder the buttons contacts

47
00:06:27,400 --> 00:06:29,880
Are they sitting nice and flat?
Good.

48
00:06:31,280 --> 00:06:34,040
Place the audiojack between the buttons

49
00:06:34,520 --> 00:06:38,560
Make sure it sits flat as well

50
00:06:39,560 --> 00:06:44,040
Solder the contacts

51
00:06:55,420 --> 00:07:01,980
Shiny connector is shiny

52
00:07:04,140 --> 00:07:08,260
The matrix has a mark.
It will read 1088BS or something similar

53
00:07:08,660 --> 00:07:11,480
The mark MUST be on the right side where PIN1 is labeled on the PCB.

54
00:07:11,780 --> 00:07:15,980
This is IMPORTANT. 
Don't screw this up.

55
00:07:17,440 --> 00:07:23,300
Now.. Solder the pins.

56
00:07:23,440 --> 00:07:24,400
That was fast!

57
00:07:25,960 --> 00:07:30,440
Cut off the excess material from the pins.

58
00:07:31,200 --> 00:07:36,580
I forgot to speed up that part .. :(

59
00:07:41,000 --> 00:07:42,860
Booooooring

60
00:07:46,580 --> 00:07:50,040
Yes! Finally!

61
00:07:50,740 --> 00:07:53,060
Insert the battery

62
00:07:53,780 --> 00:07:56,760
+ is on the batterholder - on the PCB

63
00:07:57,240 --> 00:07:59,580
WAHAHAAHAHAHAAAAAA!!!!!
You did it!

64
00:08:00,840 --> 00:08:04,840
Congratulations!
You just learned how to solder SMD by hand

65
00:08:07,220 --> 00:08:11,880
It was not that hard. Was it? :)